铸铝激光熔融处理后的组织与性能

应用光学和电子显微镜及显微硬度计研究了铸造Al-Si合金经激光表面熔融处理后的组织和性能。指出,组织分熔化区、过度区和基体三层。在熔化区中树枝状先共晶α相的平均宽度由原始组织的20～40μm细化到2～3μm,同时共晶组织也被大大细化。这些变化使显微硬度值由67.4提高至109～115.     

RETARDATION AND REPAIR OF FATIGUE CRACKS BY ADHESIVE INFILTRATION

Abstract— This paper presents results which demonstrate that polymeric filler materials, such as low-viscosity epoxies, can be vacuum-infiltrated into fatigue cracks in 7050 aluminium alloy to produce significant levels of fatigue crack retardation. It was found that the main test variable affecting the degree of retardation was the stress level at which the adhesive was introduced and cured. Two infiltrated adhesives were tested.
Infiltration at 0% (of the original) peak fatigue stress level produced negligible retardation, while infiltration at the 80% stress level produced about 300% increase in fatigue life for one adhesive and 3000% for the other adhesive. For the highest infiltration stress level both crack-face wedging and adhesion contributed initially to the retardation, but the adhesive component ceased after a crack grew through the adhesive to the original crack tip position. The results are discussed in terms of the applicability of the technique to highly-stressed aircraft components.     

化学镀Ni—P镀层的X射线衍射研究

根据X射线衍射分析结果,对化学镀高P(含P>11wt％或19at％)Ni-P镀层加热时效时,镀层成分和加热温度对结构转变的影响作了研究,结果表明,高P共晶、过共晶(含P>11wt％或19at％)合金的结构转变有如下特征:(1)相同加热时效条件下,Ni-P合金的结构转变与成分有密切关系:(2)对同一成分的过共晶合金,Ni-P合金的结构转变与时效温度密切相关;(3)过共晶合金在290～360℃温度范围内时效处理,出现Ni_xP_y介稳相,X射线衍射分析认为Ni_xP_y为Ni_(12)P_5。     

Effect of temperature on recombinant protein production using the Bm5/Bm5.NPV expression system

A series of experiments have been conducted using a recombinant baculovirus/insect cell expression system (Bm5/Bm5.NPV.CAT) to establish the optimum temperature for both cell growth and virus infection. Bm5 cell growth was found to be limited at temperatures below 22°C and ceased completely at temperatures above 34°C. In the range between 24 and 28°C, final cell densities always reached 96% of the highest achievable viable cell density. The shortest population doubling time was obtained at 28°C. Overall, a consistent increase in metabolism with increasing temperatures was observed. During the infection/viral replication phase, an increase in the temperature from 25 to 31°C resulted in a faster decrease in viable cell density and an earlier production of chloramphenicol acetyltransferase (CAT). Furthermore, protein yield at temperatures above 28°C was significantly reduced. Overall, the best temperature for the infection phase for the Bm5/Bm5.NPV expression system was found to be 25°C when the cells are cultured in serum free media.     

高速转镜相机中倾斜光束的成象

本文通过建立几何模型 ,讨论了高速转镜相机光束倾斜入口的成象原理。证实了倾斜光束入口在转镜旋转时成象点的扫描轨迹是在以入射点为顶点 ,以成象点和入射点的连线为母线扫出的正圆锥底面的平面内 ,从而把空间光学的复杂设计问题简化成平面上的设计。此原理已用于 PDF- 2 0 0型平面转镜等待式分幅相机的设计     

液态金属钠高温沸腾实验回路应力分析与强度计算

本文主要完成了液态金属钠高温沸腾实验回路的应力分析与计算，确定了回路高温区连接管系的布置型式和支吊架系统，是该回路总体设计的重要组成部分。     

高温超高压处理HDPE的WAXD及FT－IR研究

用ＷＡＸＤ和ＦＴ－ＩＲ对高温超高压处理前后的ＨＤＰＥ进行了研究。发现经５．０ＧＰａ的高压处理或２００℃下４．０ＧＰａ的高压同时处理后的ＨＤＰＥ分子链的化学结构未发生变化。ＨＤＰＥ晶体中（２００）面与（１１０）面衍射峰的峰高比（γ）随着压力的升高而增大，表明ＨＤＰＥ分子链在超高压作用下发生了取向排列，且升高温度更有利于这种取向排列，但当压力增大至５．０ＧＰａ及温度升高至２００℃时，γ反而大幅度下降。     

新型引线热浸镀锡合金的研究

分析比较了进口锡与国产锡的成分和性能。设计出了新型的引线热浸镀锡合金，它具有较低的工作温度、优良的抗氧化性、流动性和可焊性。     

微酸性光亮锡铅合金镀液分析方法

提出锡铅合金液中Ｓｎ＾２＋，Ｓｎ（ＩＶ），ＰＢ＾２＋、ＥＤＴＱＡ、柠檬酸三钠的分析方法。     

Adaptive control in a heating vessel: A comparative study

This paper presents experimental results obtained in temperature adaptive control of a heating vessel. A non-linear model of the process showed that the feed flow rate causes severe variations in time constant and process gain. An extended horizon self-tuning controller and two different model reference adaptive controllers were tested. The influence of design parameters on control performance for each algorithm was assessed. The control system was disturbed with load and setpoint changes.